Switchmode Battery Chargers...

BCS - Durst Fully Automatic Premium Switchmode Battery Chargers

Solve Battery Problems, just “set and forget”

Set and Forget you say?, Absolutely, Durst Switchmode Battery Chargers are micro processor controlled to vary the charge rate in three stages from what is known as the Bulk Rate (about 60 – 70% charged) down to the Absorption Rate (almost fully charged) then finally the Float Mode (minimal charge rate) that will maintain the battery in a full state of charge and maximise battery life. Should the level of charge decrease, the charger will automatically increase to compensate thereby maintaining full battery charge. We did say automatic and we did say Set and Forget, it is that simple.

The user friendly LED, as fitted to most models, will tell you which mode the charger is in and therefore at what stage of charge the battery is in. Available in either 12 or 24 volt and in either single or multiple channels (charge more than one battery at a time), the Durst Range of quality switchmode chargers will cater for whatever type of battery you are charging whether it is Gel, Wet Cell, Calcium, or AGM.

If your application is Automotive, Marine, Mobile Home or Caravan, Mobility Appliances, Industrial or Commercial Applications, Solar, Deep Cycle, UPS Standby, it doesn’t matter; there is a quality Durst Switchmode charger that will suit your requirements irrespective of what they might be.

Make life a little less complicated and take the grief out of maintaining batteries. It may cost you a lot less than you think. Take a look at what’s on offer.

With the Durst BCS Range of Switchmode chargers you will receive the highest level of quality and performance that you would expect from a Durst product. Available in 12 volt (15, 25 45 Amp) or 24 volt (15 and 25 Amp) versions, the BCS range is available in single, dual or triple channel versions, depending on the model, and are recommended for batteries from 50 to 800 Ampere Hour Rating.

Complimenting these chargers are accessories such as remote controls and temperature sensors that make the Durst BCS range ideal for permanent installations such as Marine and Industrial situations where access to the charger and/or batteries may be limited.

Adjustable voltage and timer settings noted in the enclosed instruction book make the BCS range suitable for charging any type of battery.

FEATURES OF THE BCS RANGE

• Fully Automatic Switchmode Operation, Fast, Safe, Efficient and Economical to run
• Input Voltage 170 – 270 Volts AC @ 50Hz
• Overcharge and Short Circuit protection
• Spike and Surge Suppression
• Insulated Output Terminals to prevent accidental contact
• Australian Electrical Standard and EMC Compliant
• Can be used as a DC Power Supply
• Optional Remote Control and Temperature Sensor

 BCD - Durst BCD Workshop Range of Battery Chargers

Charge Batteries in Vehicle without damage to ECU or other Electronic Components (Even Calcium Batteries!)

Utilising the many features, simplicity and quality of the Durst BCS Range noted previously, Durst have taken it a step further and enclosed these models in a protective powder coated steel case for workshop use that is conveniently fitted with a carry handle, rubber feet, cables and insulated clamps.

The BCD Range maintains FULL BATTERY VOLTAGE whilst the Technician is working on the vehicle or downloading data so there are no missed readings from scanners or other associated diagnostic equipment. Just ask Audi, Mercedes Benz, Land Rover, Porsche, Ford, GMH, BMW, Toyota etc throughout Australia and New Zealand.

Available in 12 volt (15, 25, 50 Amp) or 24 volt (15 and 25 Amp) versions, the BCD range is available in single, dual or triple channel versions, depending on the model. Multiple channel versions come with a lead set for each channel. As with the BCS range, remote control panel and a battery temperature sensor are available as options. The uses and applications for these premium chargers are endless.

BCS-A - Durst BCS-A Range of Battery Chargers

Big on Quality and Reliability but not on price, that‘s the Durst BCS–A Range.

Complimenting our Higher Amperage BCS Range, the compact, lightweight BCS-A range puts out honest amperage figures in a robust package. Made from extruded aluminium, (no plastic here), the BCS-A range of chargers are fully automatic, set and forget units that will punch way above their weight.

Utilising switchmode technology and fitted with thermostatically controlled cooling fans, these units show remarkable reliability and will operate for hours on end without missing a beat. Available in 12 volt (3, 6, 10 and 20 Amp) and 24 volt (4, 7, and 12 Amp) the compact design is ideal where space is at a premium.

Designed to charge any type of battery, including Gel, Wet Cell, Calcium or AGM, the BCS-A Range will adapt to just about any situation or application that you can come up with and save you money at the same time. As we say, just set and forget!

Available with optional plug to suit mobility scooters, wheel chairs etc.

Fully Automatic Durst Smartchargers...

"Solve Battery Problems" - Set and Forget

Durst now offer the Fully Automatic Set & Forget SMARTCharge Solution for all Automotive, Marine, Mobile Home, Electric Scooters, Golf Carts, Solar, Deep Cycle, UPS Standby, Industrial & Commercial Applications.

Simply connect the battery to the SMARTCharger and let it auto-run the charging program. The user friendly LED display lets you clearly understand the status of the charging mode. You can select the battery type switch for Gel (maintenance free) battery or Flooded (wet) battery to get optimum performance. At the Float charging mode, you can select the equalizing switch to choose the best voltage level for maximum battery life.

Available in a comprehensive range of single & multi outputs in 12,24,36,48 Volts, from 5 to 50 Amps & are recommended for batteries 18-800AH.

Multi Channel Outputs on some models: The charger will select the correct current for each bank of batteries connected and automatically adjust to the battery voltages sensed.

SMART Charger Features: • Fully Automatic Fast & Safe • High Efficiency & cheaper to run • Input Voltage 170-270 Volts AC 50 Hz • Overcharging Protection • Short Circuit Protection • Spike & Surge Suppression • Isolated Output Terminals • Battery Type Selector: Gel/Flooded • Equalize Float Voltage Choice • Three Stage Charging Indicator LEDS • Switch mode Design • NASA Developed Technology • Eliminates Sulphation • User Friendly • Compact & Light Weight • Australian Electrical Standard & EMC Compliant • Suitable Also a Power Supply • Multi Channel Outputs

One charger to suit all types of batteries: Gel-AGM (Maintenance Free) & Flooded (Wet) Lead Calcium-Lead Acid-VRLA Deep cycle etc.

How the Fully Automatic SMARTCharger works:
SMARTCharger provides a fast, safe and accurate charge with a three stage charge sequence:

• 1st stage - Bulk: The battery is charged at full rated output current of the charger until the battery reaches the absorption voltage. In this stage 60%-70% of the battery’s capacity is replaced.
• 2nd stage - Absorption: The charging current falls steadily and the battery voltage stays at the absorption voltage level while the remaining 30%-40% of capacity is replaced.
• 3rd stage - Float: When the battery is fully charged. The charger voltage is decreased and is held constantly at the set float voltage. This float charging voltage will not damage the battery but replenishes any loss of internal battery discharge. The equalize float voltage selector switch allows you to choose the best voltage to obtain maximum battery capacity.

Make sure your batteries are even more durable with our Set & Forget SMARTCharger
Deficient chargers “kill” thousands of batteries every year and in the past the best solution was to factory calibrate the charger to a specific battery type which is OK as long as it is not used for another type of battery. Many chargers available on the market today, claim to suit all battery types!! They achieve this by averaging boost & float charge voltages. This is a compromise & will not charge the complex variety of batteries to full capacity & can reduce battery life. Only the Durst SMARTCharger ensures that batteries are not overcharged or undercharged.

Charge Battery in Vehicle without damage to ECU or Alternator (Even Calcium Batteries!)
These sophisticated Durst SmartChargers are light-weight, compact and efficient and will automatically charge, without requiring monitoring just SET & FORGET. They have been specially developed for use with all Deep Cycle, Sealed Lead-Acid, Calcium Lead and Automotive/Marine batteries including immobilised Gel Electrolyte Batteries with a nominal voltage of 12 volts and up to 800 AH.

Charging begins immediately the battery is connected. The output of the charger is electronically protected against short circuit and extremely deeply discharged batteries. Charger maintains FULL BATTERY VOLTAGE when technician is working on the vehicle so there are no missed readings from scanners & associated diagnostic equipment. Models range from 4amp all the way up to 50amp units. 24volt models are also available for Truck – Heavy vehicle applications. As supplied to Ford, GMH, BMW, Mercedes, Range Rover, Porsche, Toyota. Etc throughout Australia & NZ

	HOME
Copyright  2003-08, Durst Motor and Electric Industries Pty Limited Phone: intl+ 61 2 9660 1755  Email: sales@Durst.com.au
Images are not to any scale.  Specifications are subject to change without notice. Any errors, inaccuracies or misdescriptions must be accepted.